| Item |
Specification |
Principal
control
functions |
Control system |
Sinusoidal PWM control |
| Rated output voltage |
Adjustable within the range of 50 to 600V by correcting the supply voltage (not adjustable above the input voltage) |
| Output frequency range |
0.5 to 500.0Hz, default setting: 0.5 to 80Hz, maximum frequency: 30 to 500Hz |
| Minimum setting steps of frequency |
0.01Hz: operation panel setting, 0.1Hz: analog input (when the max. frequency is 100Hz). |
| Frequency accuracy |
Digital setting: within +/-0.01% of the max. frequency (-10 to +60 degreeC)
Analog setting: within +/-0.5% of the max. frequency (25 degreeC +/-10 degreeC) |
| Voltage/frequency characteristics |
V/f constant, variable torque, automatic torque boost, vector control, automatic energy-saving, dynamic automatic energysaving
control. Auto-tuning. Base frequency (25 - 500Hz) adjusting to 1 or 2, torque boost (0 - 30%) adjusting to 1 or 2,
adjusting frequency at start (0.5 - 10Hz) |
| Frequency setting signal |
Potentiometer on the front panel, external frequency potentiometer (connectable to a potentiometer with a rated impedance
of 1 - 10kohm), 0 - 10Vdc (input impedance: VIA/VIB=30kohm), 4 - 20mAdc (Input impedance: 250ohm). |
| Terminal board base frequency |
The characteristic can be set arbitrarily by two-point setting. Possible to set individually for three functions: analog input (VIA and VIB) and communication command. |
| Frequency jump |
Three frequencies can be set. Setting of the jump frequency and the range. |
| Upper- and lower-limit frequencies |
Upper-limit frequency: 0 to maximum frequency, lower-limit frequency: 0 to upper-limit frequency |
| PWM carrier frequency |
Adjustable within a range of 2.0 to 16.0Hz (default: 12kHz) |
| PID control |
Setting of proportional gain, integral gain, differential gain and control wait time. Checking whether the amount of processing amount and the amount of feedback agree. |
Operation
specifications |
Acceleration/deceleration time |
Selectable from among acceleration/deceleration times 1, 2 or 3 (0.0 to 3200 sec.). Automatic acceleration/deceleration function.
S-pattern 1 or 2, and S-pattern value adjustable. Forced rapid deceleration and dynamic rapid deceleration function. |
| DC braking |
Braking start-up frequency: 0 to maximum frequency, braking rate: 0 to 100%, braking time: 0 to 20 seconds, emergency
DC braking, motor shaft fixing control |
| Dynamic braking |
Control and drive circuit is built in the inverter with the braking resistor outside (optional). |
Input terminal function
(programmable) |
Possible to select from 76 functions, such as forward/reverse run signal input, jog run signal input, operation base signal
input and reset signal input, to assign to 8 input terminals. Logic selectable between sink and source. |
Output terminal functions
(programmable) |
Possible to select from 58 functions, such as upper/lower limit frequency signal output, low speed detection signal output, specified speed
reach signal output and failure signal output, to assign to FL relay output, open collector output and RY output terminals. |
| Forward/reverse run |
The RUN and STOP keys on the operation panel are used to start and stop operation. The switching between forward run and
reverse run can be done from one of the three control units: operation panel, terminal board and external control unit. |
| Jog run |
Jog mode, if selected, allows jog operation from the operation panel or the terminal board. |
| Preset speed operation |
Base frequency + 15-speed operation possible by changing the combination of 4 contacts on the terminal board. |
| Retry operation |
Capable of restarting automatically after a check of the main circuit elements in case the protective function is activated. 10 times (Max.) (selectable with a parameter) |
| Various prohibition settings |
Possible to write-protect parameters and to prohibit the change of panel frequency settings and the use of operation panel for operation, emergency stop or resetting. |
Regenerative power
ride-through control |
Possible to keep the motor running using its regenerative energy in case of a momentary power failure. |
| Auto-restart operation |
In the event of a momentary power failure, the inverter reads the rotational speed of the coasting motor and outputs a frequency appropriate
to the rotational speed in order to restart the motor smoothly. This function can also be used when switching to commercial power. |
| Drooping function |
When two or more inverters are used to operate a single load, this function prevents load from concentrating on one inverter due to unbalance. |
| Override function |
The sum of two analog signals (VIA/VIB) can be used as a frequency command value. |
| Failure detection signal |
1c-contact output: (250Vac-0.5A-cos = 0.4) |
Protective
function |
Protective function |
Stall prevention, current limitation, over-current, output short circuit, over-voltage, over-voltage limitation, undervoltage, ground fault, power supply phase
failure, output phase failure, overload protection by electronic thermal function, armature over-current at start-up, load side over-current at start-up, overtorque,
undercurrent, overheating, cumulative operation time, life alarm, emergency stop, braking resistor over-current/overload, various pre-alarms |
| Electronic thermal characteristic |
Switching between standard motor and constant-torque VF motor, switching between motors 1 and 2, setting of overload
trip time, adjustment of stall prevention levels 1 and 2, selection of overload stall |
| Reset function |
Function of resetting by closing contact 1a or by turning off power or the operation panel. This function is also used to save and clear trip records. |
Display
function |
Alarms |
Stall prevention, overvoltage, overload, under-voltage, setting error, retry in process, upper/lower limits |
| Causes of failures |
Over-current, overvoltage, overheating, short-circuit in load, ground fault, overload on inverter, over-current through arm at start-up, overcurrent
through load at start-up, CPU fault, EEPROM fault, RAM fault, ROM fault, communication error. (Selectable: Over-current
through braking resistor/overload, emergency stop, under-voltage, low voltage, over-torque, motor overload, output open-phase) |
| Monitoring function |
Operation frequency, operation frequency command, forward/reverse run, output current, voltage in DC section, output voltage, torque,
torque current, load factor of inverter, integral load factor of PBR, input power, output power, information on input terminals, information on
output terminals, version of CPU1, version of CPU2, version of memory, PID feedback amount, frequency command (after PID), integral
input power, integral output power, rated current, causes of past trips 1 through 4, information on life alarm, cumulative operation time |
| Past trip monitoring function |
Stores data on the past four trips: number of trips that occurred in succession, operation frequency, direction of rotation, load current, input
voltage, output voltage, information on input terminals, information on output terminals, and cumulative operation time when each trip occurred. |
| Output for frequency meter |
Analog output (1mAdc full-scale DC ammeter or 7.5Vdc full-scale DC voltmeter/rectifier type AC voltmeter, 4 to 20mA/0
to 20mA output) |
| 4-digit 7-segments LED |
Frequency: inverter output frequency.
Alarm: stall alarm “C”, overvoltage alarm “P”, overload alarm “L”, overheat alarm “H”.
Status: inverter status (frequency, cause of activation of protective function, input/output voltage, output current, etc.) and parameter settings.
Free-unit display: arbitrary unit (e.g. rotating speed) corresponding to output frequency.
|
| Indicator |
Lamps indicating the inverter status by lighting, such as RUN lamp, MON lamp, PRG lamp, % lamp, Hz lamp, frequency
setting potentiometer lamp, UP/DOWN key lamp and RUN key lamp. The charge lamp indicates that the main circuit
capacitors are electrically charged. |
| Environments |
Use environments |
Indoor, altitude: 1000m (Max.), not exposed to direct sunlight, corrosive gas, explosive gas / vibration (less than 5.9m/s2) (10 to 55Hz) |
| Ambient temperature |
-10 to +60 degreeC Note 9,10) |
| Storage temperature |
-25 to +70 degreeC |
| Relative humidity |
20 to 93% (free from condensation and vapor). |
Note 9. Above 40 degreeC : Remove the protective seal from the top of the inverter. Above 50 degreeC: Remove the seal from the top of the inverter and use the inverter with the rated output current reduced.
Note 10. If inverters are installed side by side (with no sufficient space left between them) installation: Remove the seal from the top of each inverter.
When installing the inverter where the ambient temperature will rise above 40 degreeC, remove the seal from the top of the inverter and use the inverter with the rated output current reduced.
